B&O Special Cables

Link your Bang and Olufsen music system to your new Beosound Level, Balance, Stage, Core, Edge or Shape speakers!
Use this cable to connect your legacy B&O system with Powerlink outputs to your new B&O speaker.

Last cable (1 pieces), no longer in stock

Will be replaced for these.

Connect another brand of subwoofer or another brand of speakers (active) to the existing Powerlink connections of the B&O system (center/master/sound/ouverture)

Din7 to 2 x rca (powerlink to 2 x tulip)

Cable is also suitable for connecting from the power link of a BeoMaster/Centre/Sound/Overture to another brand of amplifier.

Please note, if no speakers are connected to a BeoMaster/Sound/Center/Overture, the speaker sense is also required.

AUX cable to 2 x RCA, DIN7 fits directly on the aux connection of the BeoSound/Center/Master/Ouverture

DIN7 to 2 x RCA, also for bluetooth with rca as connection.

Quantity in Stock,

3M- 12 pieces
5M - 12 pieces
7M - 9 pieces
10M - 10 pieces

Beosound 9000 Speaker Sense Adapter (Gives Remote Control Functions When No Speakers Are Connected)

Beosound 9000 Speaker Sense Adapter When you use Beosound 9000 without speakers connected (ie. via a TV or amplifier), it will ignore remote control commands.

Simply add this adapter to the spare PL socket to restore full functionality!

Connect your Beosound/center via powerlink to the latest generation of TVs.

This cable is suitable for the PIN9 (AV-in) on your TV, the types Avant MKI, Beoplav V1 and Beovision 11 have this connection.

The Avant MKII, horizon, harmony and eclipse have minijack as LINE-IN.

powerlink connection (din8) in the powerlink Pin9 in the tv, put tv on av input and play cd or radio from the connected component, keep in mind that the connected component must increase its volume which it should give or the TV will not receive a signal. First try to set the volume to 50 and use your default volume of the TV, if it is too low you can increase the volume of the connected device, if it is correct it can be programmed so that you do not have to increase it during use.

When using the BeoSound 9000 you also need the speaker sense if there are no speakers connected to.

Use this cable to connect external audio devices to a Beovision with pin9 as the input line.

This pin9 connection is on the Beovision 11-12, Avant MKI TVs, view your device before ordering it.

To get a good display, the connected device must have sufficient volume to receive an input into the TV, the TV has a regulated input (volume controlled).

RCA/Tulp to Powerlink/DIN to connect beolab via RCA/LINE, Din to tulip (for receiver)
Super High Quality cable 4.5 mm shielded Professional sound quality cable.

This cable fits the: Beolab 3/9/4002/6002/8002.

From Sonos Pre-Out, amplifier Pre-Out or the node2/3 Pre-out.

Connection via Line cable, the switch must be set to LINE.

REAN connectors Din7- tulip/gold
Cable thickness per connection, 4.5 mm shielded.

Unclear, email us for information.

Concerns 1 set of 2 cables: one for left and one for right speaker,

This cable is not for:

Beolab1
Beolab2
Beolab4
Beolab5
Beolab7
Beolab10
Beolab11
Beolab2500
Beolab3000
Beolab4000
Beolab4500
Beolab5000
Beolab6000
Beolab8000
Beolab Penta.

Please don't try it, it just won't work

You have need for these speakers the normally tulip cable, these find you here.

RCA to DIN special cable to connect beolab for LINE, chepa cable 2,5 mm fat.

Beolab 3/9/4002/6002/8002 are new BeoLab speakers without the RCA (LINE) connection, this RCA connector connection has been changed to a connection to the existing DIN8 connection from B&O.

With this cable you can still connect the newer speakers to Sonos or an amplifier/node2 by setting the BeoLab to LINE.

Normal powerlink connector and rca tulp

Unclear, email us for information.

This cable is not for the,

BeoLab 1/2/4/5/7/10/11/2500/3000/4000/4500/5000/6000/8000/penta

Connect the Beolab 11 (subwoofer) via LINE,

2 types, Line via Minijack or via RCA,

This concerns the RCA-Tulp to powerlink.

Also for Non B&O sub with only one rca connection.

Connect the Beolab 11 (subwoofer) via LINE,

2 types, Line via Minijack or via RCA,

This concerns the Minijack to powerlink, 3 & 5 meters

Connect BeoLab speaker via headphone output/ipad/ipod/tablet/gsm tv or bluetooth.

Intended for: BeoLab 3/9/4002/6002/8002

This cable is not suitable for the:
BeoLab 1/2/4/5/7/10/11/2500/3000/4000/4500/5000/6000/8000/penta

Connected to headphone output pc/gsm/tabet/tv or the Hall-Bluetooth

Cable for headphone output to amplifier or bluetooth to amplifier.
 
Can also connect Apple Airport to div. BANG & OLUFSEN components, or Audio-In tuner / TV

Or connection to Beosound4 to GSM / airport / TV

Cables are gold plated.
 
For,
BeoLab 1/4/3000/4000
beolab 4500/5000/6000
beolab 8000 and penta

Via (tulip) on LINE

Also for connection to the hall-bluetooth

Special for B&O pick-ups with earth cable.

High Quality cable.

Length ca 1 m

DIN5 to 2 X RCA without earth cable.

High Quality cable, lenght ca 90 cm

Latest length, is no longer in stock

1 X 3 meter

5 X 5 meter

Short instructions for connecting via a Beolink Converter 1611, a better connection.

Finally, a direct connection to your Beolab 3500 or LCS9000 speaker without Masterlink!

Use this cable to connect your B&O Beolab 3500 or LCS9000 speaker to an iPod, non-B&O TV or Airport Express and stream your music with Airplay from your iPhone or Apple device.

This high quality cable will allow you to connect a Bang and Olufsen Beolab 3500 or LCS9000 link room speaker directly to your Airport Express, iPod, non-B&O TV or any device with a headphone socket. This will let you stream iTunes music and other audio from your iPhone, iPad or Mac wirelessly to your Bang and Olufsen Beolab 3500 or LCS9000 speaker via the Powerlink or MCL socket.

Compatibility: This cable will fit both versions of Beolab 3500. Beolab 3500 mk.1 and LCS9000 speakers have serial numbers lower than 19343452, so please order the mk.1 cable option for these speakers.  If the serial number of your speaker is 19343452 or above, you have the mk.2 speaker, so please order the mk.2 cable option.  Please check compatibility before you buy - if you are in any doubt, please ask!

A B&O remote (either Beo4 or Beolink 1000) is needed to set the speaker to MCL mode (Beolab 3500 mk.1/LCS9000) or Powerlink mode (Beolab 3500 mk.2) each time it is switched on. For Beolab 3500 mk/1 or LCS9000, please press MENU 0 4 GO on a Beo4 or MENU 0 4 PLAY on a Beolink 1000, or for Beolab 3500 mk.2 please press MENU MENU 0 4 GO on a Beo4 or MENU MENU 0 4 PLAY on a Beolink 1000 (please ensure that the "GO" or "PLAY" button is only pressed briefly).  Volume control is then managed from the connected device (eg. TV, iPod, etc).  To turn off the speaker, press the “Power Off” button on the remote as usual.
We chose 5 pin DIN cables for the Beolab 3500 mk.2 cables as they fit and work perfectly in the 7 pin DIN Aux sockets on most B&O systems. Little known fact: the extra two pins are only used for sending remote control data to other B&O products - hence they are spare in this application.  Our Beolab 3500 mk/1 and LCS9000 cables do need the extra two pins, so these have 7 pin plugs fitted!

Streaming via masterlink cables or RJ45 network cables will be possible from mid-March, see this page for more information.

 Streaming over masterlink cables or RJ45 network cables to the Lab2000 will be possible from mid-March, see this page for more information.

With cable works,